Jola Spezialschalter K. Mattil & Co. KG
Klostergartenstraße 11-20
D-67466 Lambrecht
Phone: +49 63 25 / 188-01
 
Level controllers Leakage detectors Other Jola products Search via product names Control of the chemical resistance
Overview of the product range Quality management system Addresses: Jola and its agents Help on CD-ROM catalogue
Back to the entrance

Conductive leakage detectors
of the Leckstar range

Leckagedetektion System Leckstar
 

Leakage detectors
w i t h cable break monitoring

- for electrically conductive liquids
- for installation in normally dry rooms

Units:

Plate electrodes: PE in combination with the plate electrode PE-Z10 or PEK-Z10
Plate electrodes: PE-Z10 and PEK-Z10
Plate electrode: WDX-Z10
Cable electrode: KE-Z10
Tape electrode: BAE-Z10
Tape electrode: TE-Z10
Suspension electrodes: EHW 1-Z10, EHW 2-Z10 and EHW 3-Z10
Rod electrodes: SE 2/¾"/M-Z10, SE 2 M-Z10, S 2 M/PP-Z10, S 2 M/PVDF-Z10
and S 2 AM-Z10
Electrode relay: Leckstar 101

Leakage detectors
w i t h cable break monitoring

- for several highly aggressive acids
- for installation in normally dry rooms or humid rooms

Unit:

Cable electrode: SAE-Z10

Leakage detectors
w i t h o u t cable break monitoring

- for electrically conductive liquids
- for installation in normally dry rooms

Units:

Plate electrodes: PE und PEK
Plate electrode: WDX
Cable electrode: KE
Tape electrode: BAE
Tape electrode: TE
Tape electrode: MAE
Suspension electrodes: LWZ, EHW 1, EHW 2 and EHW 3
Rod electrodes: SE 2/¾"/M, SE 2 M, S 2 M/PP, S 2 M/PVDF and S 2 AM
Electrode relay: Leckstar 5
Electrode relay: Leckstar 5/G

Plate, cable and tape electrodes for leakage detection

For signalling the presence of an electrically conductive liquid caused, for example by burst pipes.

Plate, cable and/or tape electrodes can, for example, be used on normally dry floors or false ceilings or in normally dry pipeline and cable ducts.

Cable electrodes and tape electrodes can also be used alongside pipes or in double-pipe systems.

If the two electrode plates of a plate electrode or the two electrode cables of a cable or tape electrode come into contact with an electrically conductive liquid (e.g. water, acid etc.), an electrical contact is made and an alarm signal given.

 

Indication for the mounting of the cable electrode:

The two sensor cables of the cable electrode must be mounted parallel to one another at a distance of approx. 2 cm using the sensor cable spacers, as a greater or lesser spacing affects the response level of the system in the event of leakage.

.

Suspension electrodes for leakage detection

For signalling the presence of an electrically conductive liquid caused, for example by burst pipes.

If the two electrode rods of a suspension come into contact with an electrically conductive liquid (e.g. water, acid etc.), an electrical contact is made and an alarm signal given.

 

Rod electrodes for leakage detection

For signalling the presence of an electrically conductive liquid caused, for example by burst pipes.

If the two non-insulated electrode rod sensor surfaces of a rod electrode come into contact with an electrically conductive liquid (e.g. water, acid etc.), an electrical contact is made and an alarm signal given.

 
These units must only be mounted and connected by a qualified specialist personnel.
 
Manufacturer reserves the right to alter the design and the technical data at his own discretion.
 
The details in this brochure are product specification descriptions and do not constitute assured properties in the legal sense.